18.11.2026 | News

DIAvent® maxFlow: Precise Control of Opening Pressure for Emergency Venting

Technology & Innovation Battery Technology Development

Emergency degassing valve for traction batteries with a high venting rate

Share it on

A battery pack must offer reliable protection against water ingress, pass leak testing after production and still provide rapid degassing in an emergency. In electric vehicles, these requirements drive the rupture disks to their limits. Their opening pressures can vary significantly and they remain open after triggering. Freudenberg Sealing Technologies has developed a solution: the DIAvent® maxFlow, an emergency degassing valve with an adjustable opening pressure.

When a battery cell undergoes thermal runaway, an emergency degassing valve must quickly vent the resulting gas from the housing. Conventional rupture disks open at around 200 to 250 millibar with a variation of up to plus/minus 100 millibar.

In the closed position, the DIAvent® maxFlow seals the battery housing. Source: Freudenberg Sealing Technologies

Replacing rupture disks with a spring

The DIAvent® maxFlow uses a profiled flat spring instead. Its activation pressure can be set anywhere between 50 and 200 millibar, where the tolerance for 100 millibar is plus/minus 15 millibar. Once the interior pressure reaches this level, the spring opens almost fully in an instant. Traditional coil-spring solutions require a substantial further increase in pressure after the activation level is reached. With the DIAvent® maxFlow, there is a significant difference between the opening and closing pressures. For example, a valve can open at 70 millibar and close again only when the pressure falls to around 35 millibar. A high activation pressure prevents harmless pressure fluctuations from inadvertently opening the valve, while a lower closing pressure minimizes the residual pressure in the system.

High venting rates in compact spaces

In the open position, the profiled flat spring of the DIAvent® maxFlow shows the opening for emergency venting. Source: Freudenberg Sealing Technologies

At a differential pressure of 300 millibar, the emergency degassing rate exceeds 190 liters per second. That is 2.5 times the rate of the DIAvent® HighFlow, another valve model in the product family. With a footprint of 86 x 86 millimeters, the height of the DIAvent® maxFlow is only 12.1 millimeters when closed and 23.4 millimeters when open. The company can also produce other dimensions upon request.
Because the valve closes again, Freudenberg Sealing Technologies can test the functionality of every single unit before delivery without damaging it. This would be impossible with rupture disks.

Cover and housing set to customer request

The valve is closed during normal operation. If it closes again after a thermal event, this prevents oxygen from entering the battery housing from outside. But this also makes it difficult for extinguishing agents to reach the source of the fire. That is why different designs are possible to meet the customer’s safety concept: The standard version closes again, while another option leaves a narrow gap open to prevent access or allows the cover to detach completely for maximum venting capacity. The housing is available in plastic or aluminum.

“With the DIAvent® maxFlow, we have addressed the drawbacks of previous venting solutions in a single product, enabling us to significantly improve both safety and flexibility in battery development,” says Daniel Uhl, Head of Product Management at Freudenberg Sealing Technologies.

Additional information on the DIAvent® maxFlow can be found here: DIAvent® Pressure equalization


Technology & Innovation Battery Technology Development
Share it on

More news on the subject Technology & Innovation

Technology & Innovation

Durable Sealing Of Busbar Feedthroughs: Replacing Epoxy With Elastomer

22.10.2026 | News

Where copper wiring passes through housing walls, thermal stress can cause microcracks in conventional potting compounds. To prevent this, Freudenberg Sealing Technologies relies on bonding solutions that overcome this problem.

Read more

Technology & Innovation

Innovation Driver: Connector Seals Improve Design Flexibility in Battery Platforms

18.08.2026 | Press release

With its connector seals, Freudenberg Sealing Technologies has developed a customer-specific, configurable concept that supports new system-level approaches in the technological advancement of modern battery packs.

Read more

Technology & Innovation

DIAvent® maxFlow For High-Performance Batteries

21.05.2026 | Press release

High degassing rate and adjustable trigger pressure for sophisticated battery systems

Read more

Technology & Innovation

Modular TPE Bellows for Special-Purpose Vehicles and Industrial Applications

08.05.2026 | Press release

Freudenberg Sealing Technologies is expanding its portfolio of bellows with a new manufacturing process for small-batch production. For the first time, custom-designed bellows made of thermoplastic elastomer (TPE) can be produced with significantly reduced tooling and fixed costs. This is feasible due to a modular tooling concept developed specifically for application-specific bellows geometries in small quantities.

Read more

Technology & Innovation

FACT Surface Technology for the Environment: An Adhesive Bonding Process Without Wet-Chemicals

22.04.2026 | Press release

Can bonding processes be designed to work without wet-chemicals? Yes. With FACT, Freudenberg Sealing Technologies is establishing a new, cost-efficient, and sustainable manufacturing process.

Read more

Technology & Innovation

Freudenberg-NOK Sealing Technologies introduces FN Lube and FN Lube Plus

01.04.2026 | Press release

Purpose designed lubricants support consistent installation and material compatibility for static seal applications.

Read more

Technology & Innovation

Technology Transfer: Automotive Hydraulic Accumulators Prove Their Value in Agriculture

17.03.2026 | Press release

A hydraulic accumulator originally developed for the automotive industry is opening up new possibilities for agricultural machinery operating under extreme conditions. Freudenberg Sealing Technologies has successfully transferred proven passenger car technology to a demanding new application.

Read more

Technology & Innovation

Santa Ana Facility Wins Prestigious IndustryWeek Award

10.12.2025 | News

Freudenberg Sealing Technologies (FST) has received the 2025 IndustryWeek Best Plants Award for its Santa Ana, California facility, marking the first time an FST site has earned this distinction in the program’s 35-year history.

Read more

Technology & Innovation

Dr. Ruth Bieringer to Become President of the German Chemical Society (GDCh)

21.11.2025 | News

On January 1, 2026, Dr. Ruth Bieringer, Vice President Technology & Innovation – Material Technology at Freudenberg Sealing Technologies, takes over as president of the German Chemical Society (GDCh).

Read more