Please activate JavaScript!
Please install Adobe Flash Player, click here for download

Fluidpower GlobalCatalog_FST - Mounting aid Piston Seals

317 Mounting aid | Aide au montage Ayudas de montaje | Auxiliar de montagem HydraulicComponents|Gammehydraulique Componenteshidráulicos|Componenteshidráulicos EN PISTON SEALS What use is the best seal if it is not properly fitted or is damaged during fitting? To make sure that this doesn’t happen, Freudenberg Sealing Technologies provides you with a tailor-made range of fitting tools. Impeccable fitting is key to the performance and operational durability of a seal and thus represents a significant quality factor. With fitting aids from Freudenberg Sealing Technologies: AA you will avoid fundamental fitting errors AA you will avoid damaging the sealing lip during fitting AA you will increase the service life of the seal AA thus saving you time and expense. Two methods have proved useful in practice for fitting piston seals, irrespective of the material: using an expansion nozzle and fitting cone and using fitting strips and a calibration sleeve. 1. Fitting with expansion nozzle and fitting cone Two-component piston seals are fitted in two stages: the contact ring is fitted first and then the profile ring. This eliminates the need to calibrate the piston seal. The fitting of both the contact ring and the profile ring is carried out in each case by following the same process: AA Place the fitting cone onto the piston. AA Lay the contact ring/profile ring onto the fitting cone. AA Expand the contact ring/profile ring across the cone with the expansion sleeve and snap into the groove. 2. Fitting with a fitting strip and calibration sleeve Piston seals can also be fitted easily using approx. 30-milli­ meter wide fitting strips made from tear-resistant nylon. With this method, the rings are snapped over each other in two stages, each with two fitting strips. PTFE profile rings should be heated to approx. 80°C before fitting in water or oil. The piston seal is then calibrated in the piston bore using a calibration sleeve. FR ETANCHÉITÉ DE PISTON A quoi sert le meilleur joint s’il n’est pas monté correctement ou s’il est endommagé lors du montage ? Afin que ceci ne se produise pas, Freudenberg Sealing Technologies met à votre disposition une gamme d’outils de montage sur mesure. Un montage impeccable est crucial pour la performance et la durée de vie d’un joint, et constitue donc un critère de qualité essentiel. Grâce aux accessoires de montage de Freudenberg Sealing Technologies, AA vous évitez des erreurs de montage fondamentales, AA vous évitez des endommagements de l’arête d’étanchéité lors du montage, AA vous augmentez la durée de vie du joint, AA vous faites des économies de temps et d’argent. Pour les joints de pistons, deux méthodes de montage ont fait leurs preuves dans la pratique, indépendamment du matériau: AA le montage à l’aide du manchon d’écartement et du cône de montage. AA le montage à l’aide de bandes de montage et d’un manchon de calibrage. 1. Montage avec un manchon d’écartement et cône de montage Dans le cas de joints de pistons en deux parties, le montage doit avoir lieu en deux étapes, en montant tout d’abord l’élément de pré serrage, puis le joint profilé. Un calibrage du joint de piston n’est pas nécessaire ensuite. Le montage de l’élément de pré serrage et du joint profilé a lieu respectivement selon le même schéma: AA Poser le cône de montage sur le piston. AA Poser l’élément de pré serrage/le joint profilé sur le cône de montage. AA Etirer l’élément de pré serrage/le joint profilé au-delà du cône à l’aide du manchon d’écartement, et l’enfoncer dans la gorge. MOUNTING AID | AIDE AU MONTAGE AYUDAS DE MONTAJE | AUXILIAR DE MONTAGEM 1. Fitting with spreading nozzle and mounting cone | Montage avec outil d'écartement et cône | Construido con la difusión de la boquilla y el cono de montaje | Montado com bico espalhador e cone

Pages Overview